Корзина
47 отзывов
ЛІДЕР ЛТД
+380674093664
+380674093664
+380443311272
+380674093647

Ремонт KONICA MINOLTA bizhub 250/350/222/282

  • Услуга
  • Код: 360

от 505 грн.

+380674093664
интернет магазин
  • +380443311272
    офис
  • +380674093647
    Viber
  • +380501338004
    Сервисный центр
  • График работы
  • Адрес и контакты
возврат товара в течение 14 дней по договоренности
Ремонт KONICA MINOLTA bizhub 250/350/222/282
Ремонт KONICA MINOLTA bizhub 250/350/222/282Услуга
от 505 грн.
+380674093664
интернет магазин
  • +380443311272
    офис
  • +380674093647
    Viber
  • +380501338004
    Сервисный центр

Описание

Ремонт KONICA MINOLTA bizhub  Восстановление мфу., обмен мфу, аренда МФУ

 Коды ошибок Konica Minolta bizhub 250

  • Code: C0001
  • Description: LCT Communication Failure
    - Due to a software malfunction, etc., the time on the watchdog timer has run out and a reset is performed.
  • Remedy:
  • Code: C0202
  • Description: Tray 1 Elevator Failure
    - The Lift-Up Sensor is not unblocked even after the set period of time has elapsed after the paper lift up operation for the drawer has begun.
  • Remedy: 1 Check the motor and sensor connectors for proper connection, and correct as necessary. 2 Check the connector of each motor for proper drive coupling, and correct as necessary. 3 Check the PU1 connector for proper connection and correct as necessary. 4 PC6 I/O check. 5 PC12 I/O check. 6 PC114-PF I/O check. 7 PC123-PF I/O check. 8 M7 operation check. 9 M8 operation check. 10 M124-PF operation check. 11 M125-PF operation check. 12 Change PWB-A. 13 Change PWB-C2. 14 Change PU1.
  • Code: C0204
  • Description: Tray 2 Elevator Failure
    - The Lift-Up Sensor is not unblocked even after the set period of time has elapsed after the paper lift up operation for the drawer has begun.
  • Remedy: 1 Check the motor and sensor connectors for proper connection, and correct as necessary. 2 Check the connector of each motor for proper drive coupling, and correct as necessary. 3 Check the PU1 connector for proper connection and correct as necessary. 4 PC6 I/O check. 5 PC12 I/O check. 6 PC114-PF I/O check. 7 PC123-PF I/O check. 8 M7 operation check. 9 M8 operation check. 10 M124-PF operation check. 11 M125-PF operation check. 12 Change PWB-A. 13 Change PWB-C2. 14 Change PU1.
  • Code: C0206
  • Description: Tray 3 Elevator Failure
    - The Lift-Up Sensor is not unblocked even after the set period of time has elapsed after the paper lift up operation for the drawer has begun.
  • Remedy: 1 Check the motor and sensor connectors for proper connection, and correct as necessary. 2 Check the connector of each motor for proper drive coupling, and correct as necessary. 3 Check the PU1 connector for proper connection and correct as necessary. 4 PC6 I/O check. 5 PC12 I/O check. 6 PC114-PF I/O check. 7 PC123-PF I/O check. 8 M7 operation check. 9 M8 operation check. 10 M124-PF operation check. 11 M125-PF operation check. 12 Change PWB-A. 13 Change PWB-C2. 14 Change PU1.
  • Code: C0208
  • Description: Tray 4 Elevator Failure
    - The Lift-Up Sensor is not unblocked even after the set period of time has elapsed after the paper lift up operation for the drawer has begun.
  • Remedy: 1 Check the motor and sensor connectors for proper connection, and correct as necessary. 2 Check the connector of each motor for proper drive coupling, and correct as necessary. 3 Check the PU1 connector for proper connection and correct as necessary. 4 PC6 I/O check. 5 PC12 I/O check. 6 PC114-PF I/O check. 7 PC123-PF I/O check. 8 M7 operation check. 9 M8 operation check. 10 M124-PF operation check. 11 M125-PF operation check. 12 Change PWB-A. 13 Change PWB-C2. 14 Change PU1.
  • Code: C0209
  • Description: LCT Elevator Motor Failure
    - The Elevator Motor Pulse Sensor (PC10-LCT) cannot detect both edges of H/L even after the set period of time has elapsed while the Elevator Motor (M5-LCT) is turning backward/forward (raise/lower).
  • Remedy:
  • Code: C0211
  • Description: Bypass Lifting Motion Failure
    - The Bypass Lift Sensor (PC29) is not blocked or unblocked even after the set period of time has elapsed after the Bypass Pick-Up Solenoid (SL3) is energized after the manual feed paper take-up operation has begun.
  • Remedy: 1 Check the SL3 connector for proper connection and correct as necessary. 2 Check cam position.. 3 PC29 I/O check PWB-A. 4 SL3 operation check. 5 Change PWB-A.
  • Code: C0212
  • Description: LCT Ejection Failure
    - See PC-407 sevice manual
  • Remedy:
  • Code: C0213
  • Description: LCT Shift Gate Malfunction
    - See PC-407 sevice manual
  • Remedy:
  • Code: C0214
  • Description: LCT Shifting Failure
    - See PC-407 sevice manual
  • Remedy:
  • Code: C0215
  • Description: LCT Shift Motor Malfunction
    - See PC-407 sevice manual
  • Remedy:
  • Code: C0701
  • Description: Manual Paper Size Detection Adjustment Failure
    - The control value of the Manual Paper Size Detection Unit does not fall within the specified range when an adjustment is made of manual paper size detection.
  • Remedy: 1 Check the VR1 connector for proper connection and correct as necessary. 2 Readjust the VR1. 3 Replace VR1. 4 Change PWB-A.
  • Code: C1080
  • Description: Exit Option Communication Failure
    - The connection status of a finishing option is changed after the copier has been turned on.
  • Remedy: 1 Turn OFF the Main Power Switch, wait for 10 sec. or more, and turn ON the Main Power Switch. 2 Check the PWB-A FN and the PWB-A for proper connection, and correct as necessary. 3 Change PWB-A FN. 4 Change PWB-A.
  • Code: C1183
  • Description: Elevator Motor Ascent/Descent Drive Failure
    - See FS-530/ PU-501/ OT-602 service manual.
  • Remedy:
  • Code: C1190
  • Description: Aligning Plate 1 Drive Failure
    - See FS-530/ PU-501/ OT-602 service manual.
  • Remedy:
  • Code: C1191
  • Description: Aligning Plate 2 Drive Failure
    - See FS-530/ PU-501/ OT-602 service manual.
  • Remedy:
  • Code: C11A0
  • Description: Paper-Lifter Drive Failure
  • Remedy:
  • Code: C11A1
  • Description: Exit Roller Pressure/Retraction Failure
    - See FS-530/ PU-501/ OT-602 service manual.
  • Remedy:
  • Code: C11A2
  • Description: Saddle Exit Roller Pressure/ Retraction Failure
    -See SD-507 service manual.
  • Remedy:
  • Code: C11A3
  • Description: Shutter Drive Failure
    - See FS-530/PU-501/OT-602 service manual.
  • Remedy:

 

  • Code: C11A4
  • Description: Saddle Exit Motor Failure
    - See SD-507 service manual.
  • Remedy:
  • Code: C11A5
  • Description: Saddle In & Out Guide Motor Failure
    - - See SD-507 service manual.
  • Remedy:
  • Code: C11A6
  • Description: Saddle Layable Guide Motor Drive Failure
    - See SD-507 service manual.
  • Remedy:
  • Code: C11B0
  • Description: Staple Unit CD Drive Failure
    - See FS-530/PU-501/OT-602 service manual.
  • Remedy:
  • Code: C11B2
  • Description: Staple Drive Failure
    - See FS-530/PU-501/OT-602 service manual.
  • Remedy:
  • Code: C11B5
  • Description: Saddle Staple 1 Drive Failure
    - See SD-507 service manual.
  • Remedy:
  • Code: C11B6
  • Description: Saddle Staple 2 Drive Failure
    - See SD-507 service manual.
  • Remedy:
  • Code: C11C0
  • Description: Punch Cam Motor Unit Failure
    - See FS-530/PU-501/OT-602 service manual.
  • Remedy:
  • Code: C11D0
  • Description: Crease Motor Drive Failure
    - See SD-507 service manual.
  • Remedy:
  • Code: C2211
  • Description: IU Motor Failure
    - The IU Motor Lock signal remains set to H for a set period of time while the IU Motor is turning.
    - The IU Motor Lock signal remains set to L for a set period of time while the IU Motor remains stopped.
  • Remedy: 1 Check the M2 connector for proper connection and correct as necessary. 2 Check the M2 for proper drive coupling, and correct as necessary. 3 Check the PWB-A connector for proper connection and correct as necessary. 4 M2 operation check PWB-A PJ28A-11 (REM) M-4 5 Change PWB-A. 6 Change PU1.
  • Code: C2351
  • Description: Toner Suction Fan Motor Failure
    - The Toner Suction Fan Motor Lock signal remains set to H for a set period of time while the Toner Suction Fan Motor is turning.
    - The Toner Suction Fan Motor Lock signal remains set to L for a set period of time while the Toner Suction Fan Motor remains stopped.
  • Remedy: 1 Check the M11 connector for proper connection and correct as necessary. 2 Check the fan for possible overload, and correct as necessary. 3 Check the PWB-A connector for proper connection and correct as necessary. 4 M11 operation check PWB-A PJ5A-13 (REM) D-14 5 Change PWB-A. 6 Change PU1.
  • Code: C2431
  • Description: IU Fuse Blowing Failure
    - The fuse is not blown even after the lapse of a predetermined period of time.
  • Remedy: 1 Check the UN2 connector for proper connection and correct as necessary. 2 Remove the Developing Unit from the IU, and then replace UN2. 3 Run F8. 4 Change PWB-A. 5 Change PU1N.
  • Code: C2557
  • Description: ATDC Sensor Failure
    - The scanning value of the ATDC Sensor is less than 7 % while the IU Motor is turning.
    - The scanning value of the ATDC Sensor is more than 19 % while the IU Motor is turning.
  • Remedy: 1 Check the UN2 connector for proper connection and correct as necessary. 2 Remove the Developing Unit from the IU, and then replace UN2. 3 Run F8. 4 Change PWB-A. 5 Change PU1N.
  • Code: C255C
  • Description: ATDC Adjustment Failure
    - The adjustment of the ATDC control voltage could not be completed in the set period of time when function F8 is run.
    - The ATDC control voltage was not within the range of 5.39 V to 8.15 V when function F8 is run.
  • Remedy: 1 Check the UN2 connector for proper connection and correct as necessary. 2 Remove the Developing Unit from the IU, and then replace UN2. 3 Run F8. 4 Change PWB-A. 5 Change PU1N.
  • Code: C2654
  • Description: EEPROM Failure
    - An EEPROM where no initial data is written is detected
  • Remedy: 1 Disconnect and then connect the power cord. Turn OFF the Main Power Switch, wait for 10 sec. or more, and turn ON the Main Power Switch. 2 Check the EEPROM on the Mechanical Control Board for proper connection, and correct as necessary. 3 Change PWB-A. 4 Change EEPROM.
  • Code: C2702
  • Description: Abnormal Image Transfer Voltage
    - The image transfer voltage exceeds 100 V for the set period of time while the IU Motor remains stopped.
  • Remedy: 1 Check the installation of the Transfer Roller. 2 Change HV1
  • Code: C3451
  • Description: Fusing Warm-Up Failure (Main)
    - The Fusing Roller Thermistor does not detect the required temperature within 30 sec. after a warmup cycle has begun; therefore, the copier does not complete the warm-up cycle.
    - The temperature of the Fusing Rollers does not reach the required level even after the set period of time has elapsed during a warm-up cycle.
  • Remedy: 1 Check that the H1 comes on when the Main Power Switch is set to ON, and correct or replace as necessary. 2 Check that the H2 comes on when the Main Power Switch is set to ON, and correct or replace as necessary. 3 Check the installation of the TH1 and the TH2, and correct or clean as necessary. 4 Check the operation of the TH1. Remove CN80 (4P), and then check that the resistance across CN80-2 and -3 on the Thermistor is infinity. 5 Check the operation of the TH2. Remove CN81 (4P), and then check that the resistance across CN81-2 and -3 on the Thermistor is infinity. 6 Check the continuity of the H1. Correct or replace as necessary. 7 Check the continuity of the H2. Correct or replace as necessary. 8 Change PU1. 9 Change PWB-A.
  • Code: C3452
  • Description: Fusing Warm-Up Failure (Sub)
    - The Fusing Roller Sub Thermistor does not detect the required temperature within 30 sec. after a warm-up cycle has begun; therefore, the copier does not complete the warm-up cycle.
    - The temperature of the Fusing Rollers does not reach the required level even after the set period of time has elapsed during a warm-up cycle.
  • Remedy: 1 Check that the H1 comes on when the Main Power Switch is set to ON, and correct or replace as necessary. 2 Check that the H2 comes on when the Main Power Switch is set to ON, and correct or replace as necessary. 3 Check the installation of the TH1 and the TH2, and correct or clean as necessary. 4 Check the operation of the TH1. Remove CN80 (4P), and then check that the resistance across CN80-2 and -3 on the Thermistor is infinity. 5 Check the operation of the TH2. Remove CN81 (4P), and then check that the resistance across CN81-2 and -3 on the Thermistor is infinity. 6 Check the continuity of the H1. Correct or replace as necessary. 7 Check the continuity of the H2. Correct or replace as necessary. 8 Change PU1. 9 Change PWB-A.
  • Code: C3751
  • Description: High Fuser Temperature Failure (Main)
    - The Fusing Roller Thermistor and Fusing Roller Sub Thermistor are detected to be at a temperature above 240 °C when the Main Power Switch is set to ON.
  • Remedy: 1 Check that the H1 comes on when the Main Power Switch is set to ON, and correct or replace as necessary. 2 Check that the H2 comes on when the Main Power Switch is set to ON, and correct or replace as necessary. 3 Check the installation of the TH1 and the TH2, and correct or clean as necessary. 4 Check the operation of the TH1. Remove CN80 (4P), and then check that the resistance across CN80-2 and -3 on the Thermistor is infinity. 5 Check the operation of the TH2. Remove CN81 (4P), and then check that the resistance across CN81-2 and -3 on the Thermistor is infinity. 6 Check the continuity of the H1. Correct or replace as necessary. 7 Check the continuity of the H2. Correct or replace as necessary. 8 Change PU1. 9 Change PWB-A.
  • Code: C3752
  • Description: High Fuser Temperature Failure (Sub)
    - The Fusing Roller Thermistor and Fusing Roller Sub Thermistor are detected to be at a temperature above 240 °C when the Main Power Switch is set to ON.
  • Remedy: 1 Check that the H1 comes on when the Main Power Switch is set to ON, and correct or replace as necessary. 2 Check that the H2 comes on when the Main Power Switch is set to ON, and correct or replace as necessary. 3 Check the installation of the TH1 and the TH2, and correct or clean as necessary. 4 Check the operation of the TH1. Remove CN80 (4P), and then check that the resistance across CN80-2 and -3 on the Thermistor is infinity. 5 Check the operation of the TH2. Remove CN81 (4P), and then check that the resistance across CN81-2 and -3 on the Thermistor is infinity. 6 Check the continuity of the H1. Correct or replace as necessary. 7 Check the continuity of the H2. Correct or replace as necessary. 8 Change PU1. 9 Change PWB-A.
  • Code: C3851
  • Description: Low Fuser Temperature Failure (Main)
    - The Fusing Roller Thermistor and Fusing Roller Sub Thermistor are detected to be at a temperature below 105 °C during standby.
    - The Fusing Roller Thermistor and Fusing Roller Sub Thermistor are detected to be at a temperature below 105 °C during printing.
  • Remedy: 1 Check that the H1 comes on when the Right-Side Door is opened, then closed, and correct or replace as necessary. 2 Check that the H2 comes on when the Right-Side Door is opened, then closed, and correct or replace as necessary. 3 Check the installation of the TH1 and the TH2, and correct or clean as necessary. 4 Check the operation of the TH1. Remove CN80 (4P), and then check that the resistance across CN80-2 and -3 on the Thermistor is infinity. 5 Check the operation of the TH2. Remove CN81 (4P), and then check that the resistance across CN81-2 and -3 on the Thermistor is infinity. 6 Check the continuity of the H1. Correct or replace as necessary. 7 Check the continuity of the H2. Correct or replace as necessary. 8 Change PU1. 9 Change PWB-A.
  • Code: C3852
  • Description: Low Fuser Temperature Failure (Sub)
    - The Fusing Roller Thermistor and Fusing Roller Sub Thermistor are detected to be at a temperature below 105 °C during standby.
    - The Fusing Roller Thermistor and Fusing Roller Sub Thermistor are detected to be at a temperature below 105 °C during printing.
  • Remedy: 1 Check that the H1 comes on when the Right-Side Door is opened, then closed, and correct or replace as necessary. 2 Check that the H2 comes on when the Right-Side Door is opened, then closed, and correct or replace as necessary. 3 Check the installation of the TH1 and the TH2, and correct or clean as necessary. 4 Check the operation of the TH1. Remove CN80 (4P), and then check that the resistance across CN80-2 and -3 on the Thermistor is infinity. 5 Check the operation of the TH2. Remove CN81 (4P), and then check that the resistance across CN81-2 and -3 on the Thermistor is infinity. 6 Check the continuity of the H1. Correct or replace as necessary. 7 Check the continuity of the H2. Correct or replace as necessary. 8 Change PU1. 9 Change PWB-A.
  • Code: C4001
  • Description: Main body Communication Failure
    Communications with the Mechanical Control Board and the MFBS Board/MFBS2 Board fail.
  • Remedy: 1 Check the MFBS/MFBS2 connector for proper connection, and correct as necessary. 2 Check the PWB-A connector for proper connection, and correct as necessary. 3 Check the flat cable between MFBS/MFBS2 and PWB-A for proper connection, and correct as necessary. 4 Turn OFF the Main Power Switch, wait for 10 sec. or more, and turn ON the Main Power Switch. 5 Change MFBS/MFBS2. 6 Change PWB-A.
  • Code: C4002
  • Description: HSYNC Detection Failure
    - No SOS falling edges are detected within the set period of time after laser emission began while the Polygon Motor is turning.
    - No SOS falling edges are detected while VIA remains ON.
  • Remedy: 1 Turn OFF the Main Power Switch, wait for 10 sec. or more, and turn ON the Main Power Switch. 2 Check the PH and the PWB-A connectors for proper connection, and correct as necessary. 3 Change PH. 4 Change PWB-A.
  •  
  • Code: C4101
  • Description: Polygon Motor Failure
    - The Polygon Motor Lock signal could not be detected within the set period of time after the Polygon Motor is energized. (Faulty start detection)
    - No First Lock signals are detected during the 1- second period that starts 1 second after a First Lock signal. (Faulty lock signal detection)
    - The Polygon Motor Lock signal could not be detected after the set period of time has elapsed while the Polygon Motor is turning. (Out-of-timing lock detection)
    - The Polygon Motor Lock signal is set to ON for longer than the set period of time while the Polygon Motor remains stopped. (Abnormal lock detection)
  • Remedy: 1 Check the PH connector for proper connection, and correct as necessary. 2 Change PH. 3 Change PWB-A.
  • Code: C4721
  • Description: Main Body G/A Communication Failure
    - Communications with the gate array for expansion I/O (the IC mounted on the Mechanical Control Board) fail.
  • Remedy: 1 Turn OFF the Main Power Switch, wait for 10 sec. or more, and turn ON the Main Power Switch. 2 Check each control board and the PWB-A for proper connection, and correct as necessary. 3 Change PWB-A.
  • Code: C5102
  • Description: Main Motor Failure
    - The Transport Motor Lock signal remains set to H for a set period of time while the Transport Motor is turning.
  • Remedy: 1 Check the M1 connector for proper connection, and correct as necessary. 2 Check the M1 for proper drive coupling, and correct as necessary. 3 Check the PWB-A connector for proper connection and correct as necessary. 4 M1 operation check PWB-A PJ28A-4 (REM) M-4 5 Change PWB-A. 6 Change PU1.
  • Code: C5351
  • Description: Power Supply Cooling Fan Motor Failure
    - The Power Supply Cooling Fan Motor Lock signal remains set to H for a set period of time while the Power Supply Cooling Fan Motor is turning.
    - The Power Supply Cooling Fan Motor Lock signal remains set to L for a set period of time while the Power Supply Cooling Fan Motor remains stopped.
  • Remedy: 1 Check the M4 connectors for proper connection, and correct as necessary. 2 Check the fan for possible overload, and correct as necessary. 3 M4 operation check PWB-A PJ33A-1 (REM) D-5 4 Change PU1.
  • Code: C5352
  • Description: Cooling Fan Motor Failure
    - The Cooling Fan Motor Lock signal remains set to H for a set period of time while the Cooling Fan Motor is turning.
    - The Cooling Fan Motor Lock signal remains set to L for a set period of time while the Cooling Fan Motor remains stopped
  • Remedy: 1 Check the M5 connectors for proper connection, and correct as necessary. 2 Check the fan for possible overload, and correct as necessary. 3 M5 operation check. 4 Change PWB-A.
  • Code: C5353
  • Description: IU Cooling Fan Motor Failure
    - The IU Cooling Fan Motor Lock signal remains set to H for a set period of time while the IU Cooling Fan Motor is turning.
    - The IU Cooling Fan Motor Lock signal remains set to L for a set period of time while the IU Cooling Fan Motor remains stopped.
  • Remedy: 1 Check the M6 connectors for proper connection, and correct as necessary. 2 Check the fan for possible overload, and correct as necessary. 3 M6 operation check. 4 Change PWB-A.
  • Code: C7001
  • Description: Engine connection error
    - The system fails in checking initial engine connection when the Power Switch is turned ON.
    - The system succeeded in checking initial connection when the Power Switch was turned ON; then it fails in rechecking initial connection through the execution of a software reset when a communications error occurs during operation.
  • Remedy: 1 Check the connection between Mechanical Control Board and BCRS Board. 2 Reset the malfunction and turn OFF and ON the Power Switch. 3 Change BCRS. 4 Change PWB-A.
  • Code: C8301
  • Description: ADF Fan Motor Failure
    - See DF-620 service manual.
  • Remedy:

 

  • Code: C9701
  • Description: ADF Document Size Failure Adjustment
    - See DF-620 service manual.
  • Remedy:
  • Code: CA052
  • Description: MIO Device Failure
    - The MIO device does not operate properly
  • Remedy: 1 Turn OFF the Main Power Switch, wait for 10 sec. or more, and turn ON the Main Power Switch. 2 Check the BCRS connectors for proper connection, and correct as necessary. 3 Change BCRS.
  • Code: CC153
  • Description: Flash ROM Failure
    - The Flash ROM data was determined to be faulty when the unit was turned on.
  • Remedy: 1 Turn OFF the Main Power Switch, wait for 10 sec. or more, and turn ON the Main Power Switch. 2 The firmware data is overwritten. 3 Change PWB-A.
  • Code: CC155
  • Description: Exit Option Flash ROM Failure
    - See FS-530/PU-501/OT-602 service manual.
  • Remedy:
  • Code: CD004
  • Description: HDD error
    - When error occurs during deletion of HDD data.
  • Remedy: 1 Turn OFF the Main Power Switch, wait for 10 sec. or more, and turn ON the Main Power Switch. 2 Check theHard Disk connector for proper connection and correct as necessary. 3 Reinstall the Hard Disk. 4 Change Hard Disk. 5 Change MFBS/MFBS2.

Характеристики

Основные атрибуты
ПроизводительKonica Minolta
Тип устройстваМФУ
Тип принтераЛазерный
СостояниеБ/У

Информация для заказа

  • Цена: от 505 грн.